SB-1010 Specifications
| Main Functions | |
| Applicable standard | USB Ver.1.1 |
| Speed | Full
speed(12Mbps), Low speed(1.5Mbps) The speed is recognized/switched automatically. *1 |
| Data record method | Recording in blocks of a byte(including sync pattern) |
| Record capacity | Max. 2GB(recorded to PC's hard disk drive) *2 |
| PC interface | Parallel port(ECP) *3 |
| Port setting method | Automatic
or manual(with the following selections) I/O : 278h, 378h, 3BCh IRQ : 5, 7 DMA : 0, 1, 3 |
| I/O terminals | Two USB
ports(Ports A and B) PC PORT(IEEE1284-compliant parallel port) |
| Indicators | Full :
Lights up when connected to a full-speed device. EMPTY : Lights up when the built-in buffer memory is empty OVER : Lights up when the built-in buffer memory overflows |
| Comments | Up to 1024 byte can be entered for each log file |
| Display packets | SOF,IN,OUT,SETUP,DATA0,DATA1,ACK,NAK,STALL,PRE |
| Display filters | SOF, PRE, NAK, address, endpoint |
| Search | SOF, Setup-Token, IN-Token, OUT-Token, Data-Packet,ACK,NAK, STALL, PRE, Unknown, CRC Error(AND search for address/endpoint is possible) |
| Mark & jump | Up to 99marks can be set for each log file, and the program can jump trough these marks |
| Power Supply | 100V to 240V AC, 50/60Hz, Max. 14VA |
| Size & weight | approx. 200x53x190(mm), approx. 800g |
| Accessories | Parallel cable SB501(1), USB cable SB-011(1), Power cord(1), Software CD-ROM(1), Instruction manual(1) |
| Environment |
Operating temperature +5 to +40 oC Operating humidity 80% RH or less(no condensation allowed) Storage temperature -10 oC to +50 oC Storage humidity 80%(40 oC) or less(no condensation allowed) |
| * 1 : | Some restrictions apply if a low-speed devices is connected via USB hub. This also applied in the case of a route hub that is built into the PC. |
| * 2 : | The capacity of the built-in buffer memory is 128kB. |
| * 3 : | Daisy-chain connection and printer switching device are not supported. |
¡@
| Standard requests and descriptors that can be displayed in detail | |
| Standard requests | CLEAR_FEATURE, GET_CONFIGRATION, GET_DESCRIPTOR, GET_INTERFACE, GET_STATUS, SET_ADDRESS, SET_CONFIGRATION, SET_DESCRIPTOR, SET_FEATURE, SET_INTERFACE, SYSNC_FRAME |
| Standard descriptors | DEVICE DESCRIPTOR, CONFIGRATION DESCRIPTOR, INTERFACE DESCRIPTOR, ENDPOINT DESCRIPTR, STRING DESCRIPTOR |
¡@
|
SB-1010 controller PC |
|
| IBM PC/AT compatible with a printer port | |
| CPU | Pentium II
processor 333MHz or higher (Pentium III processor 500MHz or higher recommended) |
| Memory | 128MB or
higher (256MB or higher memory length recommended) |
| Hard disk drive | 3MB or more
free space for installation of the software A sufficient free space for communication log is also required |
| Display | XGA(1024x768) or higher resolution recommended |
| Operating System (OS) | Windows98, Windows98SE, Windows Me, Windows 2000(not guaranteed in the case of multi-processor) |
| Printer port | Use of both IRQ and DMA in ECP mode must be possible (IEEE1284 compatible parallel port*) |
|
*
¡@ |
The designed performance of the SB-1010 is not guaranteed in the case of an extension parallel card (i.e. a parallel card connected to the PCI bus, PC card adapter, notebook PC's port replicator, or replicator connected via USB interface). |
|
* ¡@ ¡@
|
Although it is recommended that use of both IRQ and DMA hardware resources is possible in ECP mode, the SB-1010 can still be used with a PC that allows only either IRQ or DMA. In this case, however, correct capture of USB traffics transferred in large quantities at high speeds(Full-speed) may sometimes not be possible. |
¡@
Top page | Functions | Connection | Panel | Specifications
Products list | brand | Model No. | Home