NFProgrammable AC Power Source DP series

Programmable AC Power Source

DP series

The DP Series has performance and functions required of a power supply
while meeting the unique needs of each customer.
Strong and smart — this is an AC power source for the future.

dp series

NF has knowledge and skill about AC power source and our DP Series incorporates new ideas while pursuing the high-quality, stable supply of power that is the fundamental role of any AC power source.

	Output control employing our unique hybrid power control technology
	User interface designed to take into account how each customer uses the equipment
	Energy-saving design to efficiently supply power and improve equipment operability

New Line-up

DP160LS: Single-phase model (16 kVA)

DP240LM: Multi-phase model (24 kVA)

DP360LM: Multi-phase model (36 kVA)

Line-up

You can select the optimal power supply from a broad range of options, from single-phase 1.5 kVA to a maximum of three-phase 144 kVA.
	The lineup includes single-phase, single-phase 3-wire, three-phase and multi-phase ( single-phase, single-phase 3-wire, or three-phase selectable) models.
	A multi-phase system (single-phase 3-wire/three-phase) can be configured by connecting multiple units of the same single-phase model.
* Same model name with same ver. of firmware

1.5 kVA

3 kVA

4.5 kVA

6 kVA

7.5 kVA

9 kVA

10.5 kVA

12 kVA

16 kVA

18 kVA

24 kVA

36 kVA

42 kVA

48 kVA

Single-phase

—

Single-phase,
3-wire *1

—

Three-phase *2

—

Multi-phase *3

—

*1 Single-phase model ×2 units
*2 Single-phase model ×3 units, 144kVA max.
*3 1-phase/1-phase 3-wire/3-phase selectable

Power input

Single phase :

100V to 230V

Three phase 3 wire :

200V to 220V

Three phase 4 wire :

380V

* Power input depends on the model.

Output Characteristics

The DP series achieves stable output with low distortion, and operates stably with high-capacity capacitor loads. With a variety of output modes and a wide output range.

AC/DC modes: AC, ACDC, DC

AC	The signal source and amplifier are AC-coupled, and the DC signal cannot be output or set. The lower limit of the frequency setting for the AC voltage in INT mode is 40Hz.
ACDC	The signal source and amplifier are DC-coupled, and DC signals and AC signals including low frequencies can be output. The lower limit of the frequency setting for AC voltage in INT mode is 1Hz. DC voltage setting is possible only for single-phase models (including single-phase mode for multi-phase models). DC voltage cannot be set for single-phase 3-wire or three-phase models(including multi-phase mode).
DC	The signal source and amplifier are DC-coupled. The voltage can be set only for DC, and the AC voltage is fixed at 0V. DC mode is available only for single-phase models (including single-phase mode for multi-phase models). DC mode cannot be set for single-phase three-wire or three-phase (including multi-phase model mode).

Output voltage/frequency

		100 V range	200 V range	Resolution
AC	Output voltage	0 V to 160V	0 V to 320V	0.1 V
AC	Frequency	AC: 40Hz to 550Hz ACDC: 1Hz to 550Hz		0.01Hz
DC	Output voltage	-227 V to +227V	-454 V to +454 V	0.1 V

Output voltage fluctuation: within ±0.15 V (75 V to150 V)/within ±0.30 V (150 V to 300 V)
(DC, 45 Hz to 65 Hz if output current is varied from 0% to 100% of maximum current)

Maximum peak current: four times the maximum current (RMS value) (corresponds to a capacitor input rectified load with a crest factor of 4)

Waveform distortion rate: 0.5% max.

Measurement Functions

In addition to voltage, current and power, the DP series optionally supports measurement of load power factor, crest factor, and up to 40th-order harmonic current. In addition, the series supports measures to control CO₂ by displaying CO₂ emissions during operation.
Measurement Items
	Voltage: RMS value, average DC value, peak value	Load power factor
	Current: RMS value, average DC value, peak value, peak hold value	Crest factor
	Power: active power, apparent power, reactive power	Sync frequency
	Harmonic current: up to 40th order	CO₂ emissions

Simple Operation

Panel operation is a breeze using the large, easy-to-read display.
The design stresses improved ease-of-use and work efficiency for users, with features such as a function for selecting three decided measurement items and displaying them enlarged, and remote operation using a remote controller.

simple operation