model

Number of parallel connections

Serial
connection number

Maximum
output voltage

Maximum
output current

Slew
rate

Maximum
peak current

A1110-5-x

-

3 units

225V peak

10A peak

240V/μs

27A peak

A1110-16-x

4 units

-

75V peak

105A peak

100V/μs

200A peak

A1110-16-x

-

3 units

225V peak

26A peak

250V/μs

55A peak

A1110-16-x

Two

Two

150V peak

55 peak

175V/μs

55A peak

A1110-40-QE-75/100

4 units

-

75/100V peak

152A peak

80V/μs

300A peak

A1110-40-QE-75/100

-

3 units

225/300V peak

40A peak

240V/μs

80A peak

A1110-40-QE-75/100

Two

Two

75/100V peak

76A peak

160V/μs

152A peak

safety equipment

·         Monitor the temperature of the output amplifier to avoid damaging the product.

·         Any current limitation is possible to avoid damage to DUT and this product.

·         Equipped with interlock function (BNC type)

BNC type

·         Overvoltage protection function (optional)

·         USB/LAN interface with disconnection prevention function

·         *LAN interface is optional

USB / LAN terminal with lock mechanism

·         Check in-flight information via interface

Voltage/current monitor

You can check the applied voltage and current with an oscilloscope. No need for voltage/current probes.

CN board (E and QE models only)

RC network compensation circuit for supplying constant load current in wide frequency range in current operation mode.
In addition to 4 types,
you can select from 6 types, including any 2 types　

Feedback sensor (optional)

KELVIN sense can be selected as the voltage sensor for feedback. In addition, a high-precision current transformer (option) is also available from the shunt resistor (standard equipment) for the current sensor.

Remote software

Full remote control is possible via LAN/USB. Controls such as output ON/OFF, mode switching, change of current feedback constant, setting of current limit, confirmation of machine temperature, safety related settings and confirmation of equipment can be done via interface.

model

A1110-

05-A

05-E

05-QE

16-A

16-E

16-QE

40-QE

40-QE-100V

Power band

DC-200kHz

Small signal frequency band

DC-1MHz

Output voltage range

±75 Vpeak

±75 V peak

±75 V peak

±100 V peak

Output current pressure range

±11 A peak

±28 A peak

±40 A peak

output

Source

500W

1000W

1200W

sink

90W

150W

300W

340W

650W

750W

Output impedance

≤10mΩ

≤60mΩ

TBD

Output
resistance adjustment

-

Output resistance adjustment range: 0 to 200
mΩ Resolution: 1 mΩ Accuracy: 0.5%

-

Output resistance adjustment range: 0 to 200
mΩ Resolution: 1 mΩ Accuracy: 0.5%

Output resistance adjustment range: 0 to 200
mΩ Resolution: 1 mΩ Accuracy: 0.5%

Option-12: Option for output resistance adjustment A1110-XX-E/QE

Slew rate

100V/μs

Possible input
rise/fall time

≥ 20 μs
(pulse rise/fall time must be greater than 20 μs)

Output connector

4mm safety jack

Voltage control
(CV) voltage gain

×10

Current control
(CC) current gain

-

1V/1A

-

1V/3A

1V/10A

Voltage monitor output

-

0.1V/1V

-

0.1V/1V

0.1V/1V

Current monitor output
() is the shunt resistance value

-

0.4V/1A (20mΩ)
1.2V/0.1A (2.5Ω)

-

0.2V/1A (20mΩ)
1.2V/0.1A (2.5Ω)

1V/10A (5.4mΩ)

Power-supply voltage

200V

External dimensions (mm)

About 449Wx
133Hx
435.5D

About 449Wx
133Hx
495D

About 449Wx
133Hx
585.5D

About 449Wx
133Hx
585.5D

mass

About 19kg

About 34 kg

About 37kg

[Model name]
Option name

A1110- ("x" is not supported)

Remark

05-A

05-E

05-QE

16-A

16-E

16-QE

40-QE

40-QE-100V

[Option02]
Internal sensor

Optional support

Optional support

×

×

Changed current sense from shunt to CT sensor.
Non-contact measurement improves current monitor waveform and feedback characteristics during CC

[Option03]
High stable gain

Optional support

Optional support

Optional support

High stability gain
(±0.1%)

[Option04]
Built-in signal generator

×

×

×

×

Optional support

Optional support

Function generator function added
DC, 0.05Hz-300kHz, sine wave, triangular wave, square wave

[Option05]
Built-in
isolation
amplifier

Optional support

Optional support

Optional support

When expanding the voltage by connecting in series, it reduces common mode noise and secures safety. (Built-in A1340-C1 function)

[Option06]
LAN
interface

×

Optional support

×

Optional support

Optional support

LAN interface with disconnection prevention function

[Option 07]
Voltage/current display

×

×

×

×

Optional support

×

×

Digital display of voltage and current on the front panel

[Option08]
KELVIN sense

×

Optional support

×

Optional support

standard equipment

The influence of wiring can be canceled during CV.

[Option09]
Output ±100V

Optional support

Optional support

×

Standard
equipment

100V power supply expansion option

[Option10]
Internal current sensor

×

×

×

×

×

×

Optional support

Changed current sense from shunt to CT sensor.
Non-contact measurement improves current monitor waveform and feedback characteristics during CC

[Option 11]
Voltage/current display

×

×

×

×

×

×

Optional support

Voltage/current digital display on front panel 3.5 digit LED ± 2% (DC-50 kHz, at 5% or more of full scale)　

[Option12]
Output resistance adjustment

×

Optional support

×

Optional support

Optional support

Output resistance adjustment range: 0 to 200
mΩ Resolution: 1 mΩ Accuracy: 0.5%

[Option13]
LAN interface
face

Optional support

×

×

Optional support

×

×

×

×

LAN interface with disconnection prevention function

[Opiont14]
Overvoltage protection

×

Optional support

×

Optional support

Optional support

The output voltage is constantly monitored, and the output is stopped when the set voltage is exceeded.

[Opiont16]
KELVIN sense

Optional support

×

×

Optional support

×

×

×

×

Sense function

■Parallel connection unit
: For A1110-16 type connection, for A1110-40 type connection

■Isolation amplifier
: A1340-C1